* chore: Set `TLS_INTERMEDIATE_SUITE` to only use TLS 1.2 ciphersuites
Removes support of the following cipher suites that are only valid for TLS 1.0 + 1.1:
- `ECDHE-ECDSA-AES128-SHA`
- `ECDHE-RSA-AES128-SHA`
- `ECDHE-ECDSA-AES256-SHA`
- `ECDHE-RSA-AES256-SHA`
- `DHE-RSA-AES128-SHA`
- `DHE-RSA-AES256-SHA`
* chore: Update TLS version min and ignore settings
These are now the same as modern settings.
* fix: Remove min TLS support workaround
No longer required now that outdated TLS versions have been dropped.
* tests: Remove support for TLS 1.0 and 1.1 ciphersuites
* tests: Remove support for TLS 1.0 and 1.1 ciphersuites (Port 25)
The removed SHA1 cipher suites are still supported in TLS 1.2, thus they've been excluded for port 25 via the `SHA1` exclusion pattern in `main.cf`.
With `reload` a change detection event during local testing can be processed in less than a second according to logs. Previously this was 5+ seconds (_plus additional downtime for Postfix/Dovecot to become available again_).
In the past it was apparently an issue to use `<service> reload` due to a concern with the PID for wrapper scripts that `supervisorctl` managed, thus `supervisorctl <service> restart` had been used. Past discussions with maintainers suggest this is not likely an issue anymore, and `reload` should be fine to switch to now 👍
---
**NOTE:** It may not be an issue in the CI, but on _**local systems running tests may risk failure in `setup-cli.bats` from a false positive**_ due to 1 second polling window of the test helper method, and a change event being possible to occur entirely between the two checks undetected by the current approach.
If this is a problem, we may need to think of a better way to catch the change. The `letsencrypt` test counts how many change events are expected to have been processed, and this could technically be leveraged by the test helper too.
---
**NOTE:** These two lines (_with regex pattern for postfix_) are output in the terminal when using the services respective `reload` commands:
```
postfix/master.*: reload -- version .*, configuration /etc/postfix
dovecot: master: Warning: SIGHUP received - reloading configuration
```
I wasn't sure how to match them as they did not appear in the `changedetector` log (_**EDIT:** they appear in the main log output, eg `docker logs <container name>`_).
Instead I've just monitored the `changedetector` log messages, which should be ok for logic that previously needed to ensure Dovecot / Postfix was back up after the `restart` was issued.
---
Commit history:
* chore: Change events `reload` Dovecot and Postfix instead of `restart`
Reloading is faster than restarting the processes.
Restarting is a bit heavy handed here and may no longer be necessary for general usage?
* tests: Adapt tests to support service `reload` instead of `restart`
* chore: Additional logging for debugging change event logs
* fix: Wait on change detection, then verify directory created
Change detection is too fast now (0-1 seconds vs 5+).
Directory being waited on here was created near the end of a change event, reducing that time to detect a change by the utility method further.
We can instead check that the directory exists after the change detection event is completed.
* chore: Keep using the maildir polling check
We don't presently use remote storage in tests, but it might be relevant in future when testing NFS.
This at least avoids any confusing failure happening when that scenario is tested.
As per deprecation notice from v11.3 release notes, and a related prior PR; this ENV is to be removed.
It's no longer considered useful, and none of the tests that configured it were actually using it for relaying anything.
- Introduced `CONTAINER_NAME` and `TEST_NAME_PREFIX` as new vars for better managing test consistency (DRY).
- `CONTAINER_NAME` replaces any repeated container name with the variable. The value will differ slightly as the prior prefix (`mail_`) has been changed to `dms-test-`.
- `TEST_NAME_PREFIX` provides a prefix value for each `@test` description string.
---
chore: Add a reference template for tests
Allows for using `load` with an absolute path instead of a relative one, which makes it possible to group tests into different directories.
Parallel tests differ slightly, loading the newer `helper/common.bash` and `helper/setup.bash` files instead of the older `test_helper/common.bash` which serial tests continue to use.
- `test_helper.bats` needs more work than this PR provides to be compatible with parallel tests, so must remain as a serial test for now.
- `spam_bounced.bats` had failures as a serial test, but works well converted to a parallel test in a future commit.
